Skip to content

Cart

Your cart is empty

Article: How to Measure Belt Length (and What Belt Sizes Really Mean)

Belt Size Guide

How to Measure Belt Length (and What Belt Sizes Really Mean)

Two belts can carry the same number and still be very different lengths. That’s because brands measure belts from different points. Once you know which method a size refers to, measuring a belt takes a minute and gives you a number you can trust.

This article is part of our complete belt size guide.

The two ways belts are measured

Total length

The whole belt, from the tip of the buckle to the end of the strap. This is how we size every Atelier Alain belt.

Buckle to middle hole

From where the leather folds around the buckle bar to the middle hole. Many brands use this method because the result lands close to your waist size, so their belt sizes look like pant sizes.

Why the two numbers differ

The total length adds the buckle and the tail beyond the middle hole. On our belts, that difference is about 25 cm (10″). A belt with a total length of 110 cm measures roughly 85 cm from the buckle to the middle hole. Before you compare sizes between brands, check which method each one uses.

Why we size by total length

Total length is a measurement of the belt itself, so it doesn’t depend on where the holes are punched or which hole counts as the middle. It’s the number you get when you lay any belt flat and measure it end to end, which makes it easy to check against a belt you already own. The trade-off is that the number is larger than your waist, so always use a size chart rather than ordering your pant size.

What you need

  • A flat surface long enough for the whole belt, such as a table or the floor.
  • A tape measure. A rigid one is easiest for a belt lying flat; a soft sewing tape works too.
  • The belt itself, unbuckled.

How to measure a belt’s total length

  1. Unbuckle the belt and lay it flat, leather side up.
  2. Straighten it out. A belt that has been worn for a while keeps a curve, and a curved belt measures shorter than it is.
  3. Place the end of the tape at the tip of the buckle, the point furthest from the strap.
  4. Measure along the leather to the very end of the strap.
  5. Note the result in inches or centimeters. One inch is 2.54 cm.

How to measure from the buckle to the hole you use

  1. Lay the belt flat and straight.
  2. Find the hole you usually fasten. It’s often slightly stretched or marked by the buckle pin.
  3. Measure from where the leather folds around the buckle bar to the center of that hole.

This number is very close to your waist at the height you wear the belt. You can use it in the “Waist” column of our size guide.

Measuring a belt for someone else

If you’re buying a belt as a gift, borrow one they wear often and measure it both ways: total length, and buckle to the most worn hole. The worn hole is usually easy to spot, with a slightly stretched edge or a mark left by the pin. The second measurement is their waist at belt height, and it gives you the most reliable size from our chart.

Measuring different buckle types

  • Pin buckles: the classic frame with a prong through a hole. Measure total length from the tip of the frame.
  • Hook and clasp buckles: common on slim dress belts. Measure from the outer end of the clasp to the end of the strap.
  • Plate buckles: a flat plate with a stud on the back. Measure from the edge of the plate.
  • Click or ratchet buckles: these belts have no holes and adjust in small steps along a track. Measure the strap from the buckle to the end, and use your waist measurement to choose, since the fit is set by the track rather than a hole.

Common measuring mistakes

  • Measuring along the curve. Always straighten the belt first.
  • Starting at the wrong end of the buckle. For total length, start at the tip, not at the bar where the leather folds.
  • Stretching a soft tape. Lay it on the leather without pulling.
  • Measuring from the last hole instead of the one you use. Use the hole that’s actually worn.
  • Trusting the number stamped inside an old belt. It may follow a different method from ours.

Turning your measurement into a size

  • You measured a belt’s total length: choose an Atelier Alain belt with the same total length, as long as your current belt fits you on its middle hole.
  • You measured from the buckle to the hole you use: treat it as your waist and read the matching length in our chart, or see what size belt do I need.
  • You have a size in centimeters and want inches, or the other way around: see belt size conversion.

Frequently asked questions

How are belts measured?

Either by total length, from the tip of the buckle to the end of the strap, or from the buckle fold to the middle hole. Atelier Alain uses total length.

Do you measure a belt with the buckle?

For total length, yes: start at the tip of the buckle. For the buckle-to-hole method, start where the leather folds around the buckle bar.

Is a 34 belt 34 inches long?

It depends on the brand. With total-length sizing, a 34″ belt is 34 inches end to end. With the middle-hole method, a “34” belt fits a 34 waist and is longer overall.

Where should I measure my waist for a belt?

Where the belt will sit, over the clothes you’ll wear it with. Our belt size guide walks you through it.

Shop men’s leather belts and women’s leather belts.

Read more

Men’s Leather Belt-Black Belt-Clicky Buckle-for Business-Men’s Gift
Belt Size Guide

What Size Belt Do I Need? Belt Size by Waist and Pant Size

Pick the right belt length from your pant size or waist measurement, with a full chart, worked examples and tips for when you’re between sizes.

Read more
Dress Belt for Women - Genuine Leather with Pin Buckle
Belt Size Guide

Belt Size Conversion: CM to Inches and EU to US Sizes

Convert belt lengths between centimeters and inches, see what common European sizes mean in US pant sizes, and read size labels correctly.

Read more